openwrt_lede/target/linux/brcm2708/patches-4.4/0142-BCM270X_DT-Adjust-overlay-README-formatting.patch

From fff71f293b81ea6aa254397236484437b491ed9c Mon Sep 17 00:00:00 2001
From: Phil Elwell <phil@raspberrypi.org>
Date: Mon, 8 Feb 2016 09:46:33 +0000
Subject: [PATCH] BCM270X_DT: Adjust overlay README formatting

---
 arch/arm/boot/dts/overlays/README | 414 +++++++++++++++++++-------------------
 1 file changed, 207 insertions(+), 207 deletions(-)

--- a/arch/arm/boot/dts/overlays/README
+++ b/arch/arm/boot/dts/overlays/README
@@ -83,58 +83,58 @@ Name:   <The base DTB>
 Info:   Configures the base Raspberry Pi hardware
 Load:   <loaded automatically>
 Params:
-        audio                    Set to "on" to enable the onboard ALSA audio
-                                 interface (default "off")
+        audio                   Set to "on" to enable the onboard ALSA audio
+                                interface (default "off")
 
-        i2c_arm                  Set to "on" to enable the ARM's i2c interface
-                                 (default "off")
+        i2c_arm                 Set to "on" to enable the ARM's i2c interface
+                                (default "off")
 
-        i2c_vc                   Set to "on" to enable the i2c interface
-                                 usually reserved for the VideoCore processor
-                                 (default "off")
+        i2c_vc                  Set to "on" to enable the i2c interface
+                                usually reserved for the VideoCore processor
+                                (default "off")
 
-        i2c                      An alias for i2c_arm
+        i2c                     An alias for i2c_arm
 
-        i2c_arm_baudrate         Set the baudrate of the ARM's i2c interface
-                                 (default "100000")
+        i2c_arm_baudrate        Set the baudrate of the ARM's i2c interface
+                                (default "100000")
 
-        i2c_vc_baudrate          Set the baudrate of the VideoCore i2c interface
-                                 (default "100000")
+        i2c_vc_baudrate         Set the baudrate of the VideoCore i2c interface
+                                (default "100000")
 
-        i2c_baudrate             An alias for i2c_arm_baudrate
+        i2c_baudrate            An alias for i2c_arm_baudrate
 
-        i2s                      Set to "on" to enable the i2s interface
-                                 (default "off")
+        i2s                     Set to "on" to enable the i2s interface
+                                (default "off")
 
-        spi                      Set to "on" to enable the spi interfaces
-                                 (default "off")
+        spi                     Set to "on" to enable the spi interfaces
+                                (default "off")
 
-        random                   Set to "on" to enable the hardware random
-                                 number generator (default "on")
+        random                  Set to "on" to enable the hardware random
+                                number generator (default "on")
 
-        uart0                    Set to "off" to disable uart0 (default "on")
+        uart0                   Set to "off" to disable uart0 (default "on")
 
-        watchdog                 Set to "on" to enable the hardware watchdog
-                                 (default "off")
+        watchdog                Set to "on" to enable the hardware watchdog
+                                (default "off")
 
-        act_led_trigger          Choose which activity the LED tracks.
-                                 Use "heartbeat" for a nice load indicator.
-                                 (default "mmc")
+        act_led_trigger         Choose which activity the LED tracks.
+                                Use "heartbeat" for a nice load indicator.
+                                (default "mmc")
 
-        act_led_activelow        Set to "on" to invert the sense of the LED
-                                 (default "off")
+        act_led_activelow       Set to "on" to invert the sense of the LED
+                                (default "off")
 
-        act_led_gpio             Set which GPIO to use for the activity LED
-                                 (in case you want to connect it to an external
-                                 device)
-                                 (default "16" on a non-Plus board, "47" on a
-                                 Plus or Pi 2)
+        act_led_gpio            Set which GPIO to use for the activity LED
+                                (in case you want to connect it to an external
+                                device)
+                                (default "16" on a non-Plus board, "47" on a
+                                Plus or Pi 2)
 
         pwr_led_trigger
         pwr_led_activelow
         pwr_led_gpio
-                                 As for act_led_*, but using the PWR LED.
-                                 Not available on Model A/B boards.
+                                As for act_led_*, but using the PWR LED.
+                                Not available on Model A/B boards.
 
         N.B. It is recommended to only enable those interfaces that are needed.
         Leaving all interfaces enabled can lead to unwanted behaviour (i2c_vc
@@ -149,19 +149,19 @@ Params:
 Name:   ads7846
 Info:   ADS7846 Touch controller
 Load:   dtoverlay=ads7846,<param>=<val>
-Params: cs                       SPI bus Chip Select (default 1)
-        speed                    SPI bus speed (default 2MHz, max 3.25MHz)
-        penirq                   GPIO used for PENIRQ. REQUIRED
-        penirq_pull              Set GPIO pull (default 0=none, 2=pullup)
-        swapxy                   Swap x and y axis
-        xmin                     Minimum value on the X axis (default 0)
-        ymin                     Minimum value on the Y axis (default 0)
-        xmax                     Maximum value on the X axis (default 4095)
-        ymax                     Maximum value on the Y axis (default 4095)
-        pmin                     Minimum reported pressure value (default 0)
-        pmax                     Maximum reported pressure value (default 65535)
-        xohms                    Touchpanel sensitivity (X-plate resistance)
-                                 (default 400)
+Params: cs                      SPI bus Chip Select (default 1)
+        speed                   SPI bus speed (default 2MHz, max 3.25MHz)
+        penirq                  GPIO used for PENIRQ. REQUIRED
+        penirq_pull             Set GPIO pull (default 0=none, 2=pullup)
+        swapxy                  Swap x and y axis
+        xmin                    Minimum value on the X axis (default 0)
+        ymin                    Minimum value on the Y axis (default 0)
+        xmax                    Maximum value on the X axis (default 4095)
+        ymax                    Maximum value on the Y axis (default 4095)
+        pmin                    Minimum reported pressure value (default 0)
+        pmax                    Maximum reported pressure value (default 65535)
+        xohms                   Touchpanel sensitivity (X-plate resistance)
+                                (default 400)
 
         penirq is required and usually xohms (60-100) has to be set as well.
         Apart from that, pmax (255) and swapxy are also common.
@@ -175,12 +175,12 @@ Name:   at86rf233
 Info:   Configures the Atmel AT86RF233 802.15.4 low-power WPAN transceiver,
         connected to spi0.0
 Load:   dtoverlay=at86rf233,<param>=<val>
-Params: interrupt                GPIO used for INT (default 23)
-        reset                    GPIO used for Reset (default 24)
-        sleep                    GPIO used for Sleep (default 25)
-        speed                    SPI bus speed in Hz (default 6000000)
-        trim                     Fine tuning of the internal capacitance
-                                 arrays (0=+0pF, 15=+4.5pF, default 15)
+Params: interrupt               GPIO used for INT (default 23)
+        reset                   GPIO used for Reset (default 24)
+        sleep                   GPIO used for Sleep (default 25)
+        speed                   SPI bus speed in Hz (default 6000000)
+        trim                    Fine tuning of the internal capacitance
+                                arrays (0=+0pF, 15=+4.5pF, default 15)
 
 
 Name:   bmp085_i2c-sensor
@@ -194,8 +194,8 @@ Name:   dht11
 Info:   Overlay for the DHT11/DHT21/DHT22 humidity/temperature sensors
         Also sometimes found with the part number(s) AM230x.
 Load:   dtoverlay=dht11,<param>=<val>
-Params: gpiopin                  GPIO connected to the sensor's DATA output.
-                                 (default 4)
+Params: gpiopin                 GPIO connected to the sensor's DATA output.
+                                (default 4)
 
 
 Name:   dwc-otg
@@ -208,15 +208,15 @@ Params: <None>
 Name:   dwc2
 Info:   Selects the dwc2 USB controller driver
 Load:   dtoverlay=dwc2,<param>=<val>
-Params: dr_mode                  Dual role mode: "host", "peripheral" or "otg"
+Params: dr_mode                 Dual role mode: "host", "peripheral" or "otg"
 
-        g-rx-fifo-size           Size of rx fifo size in gadget mode
+        g-rx-fifo-size          Size of rx fifo size in gadget mode
 
-        g-np-tx-fifo-size        Size of non-periodic tx fifo size in gadget
-                                 mode
+        g-np-tx-fifo-size       Size of non-periodic tx fifo size in gadget
+                                mode
 
-        g-tx-fifo-size           Size of periodic tx fifo per endpoint
-                                 (except ep0) in gadget mode
+        g-tx-fifo-size          Size of periodic tx fifo per endpoint
+                                (except ep0) in gadget mode
 
 
 [ The ds1307-rtc overlay has been deleted. See i2c-rtc. ]
@@ -225,9 +225,9 @@ Params: dr_mode                  Dual ro
 Name:   enc28j60
 Info:   Overlay for the Microchip ENC28J60 Ethernet Controller (SPI)
 Load:   dtoverlay=enc28j60,<param>=<val>
-Params: int_pin                  GPIO used for INT (default 25)
+Params: int_pin                 GPIO used for INT (default 25)
 
-        speed                    SPI bus speed (default 12000000)
+        speed                   SPI bus speed (default 12000000)
 
 
 Name:   gpio-ir
@@ -237,26 +237,26 @@ Info:   Use GPIO pin as rc-core style in
         not required! The key mapping and other decoding parameters can be
         configured by "ir-keytable" tool.
 Load:   dtoverlay=gpio-ir,<param>=<val>
-Params: gpio_pin                 Input pin number. Default is 18.
+Params: gpio_pin                Input pin number. Default is 18.
 
-        gpio_pull                Desired pull-up/down state (off, down, up)
-                                 Default is "down".
+        gpio_pull               Desired pull-up/down state (off, down, up)
+                                Default is "down".
 
-        rc-map-name              Default rc keymap (can also be changed by
-                                 ir-keytable), defaults to "rc-rc6-mce"
+        rc-map-name             Default rc keymap (can also be changed by
+                                ir-keytable), defaults to "rc-rc6-mce"
 
 
 Name:   gpio-poweroff
 Info:   Drives a GPIO high or low on reboot
 Load:   dtoverlay=gpio-poweroff,<param>=<val>
-Params: gpiopin                  GPIO for signalling (default 26)
+Params: gpiopin                 GPIO for signalling (default 26)
 
-        active_low               Set if the power control device requires a
-                                 high->low transition to trigger a power-down.
-                                 Note that this will require the support of a
-                                 custom dt-blob.bin to prevent a power-down
-                                 during the boot process, and that a reboot
-                                 will also cause the pin to go low.
+        active_low              Set if the power control device requires a
+                                high->low transition to trigger a power-down.
+                                Note that this will require the support of a
+                                custom dt-blob.bin to prevent a power-down
+                                during the boot process, and that a reboot
+                                will also cause the pin to go low.
 
 
 Name:   hifiberry-amp
@@ -300,65 +300,65 @@ Name:   hy28a
 Info:   HY28A - 2.8" TFT LCD Display Module by HAOYU Electronics
         Default values match Texy's display shield
 Load:   dtoverlay=hy28a,<param>=<val>
-Params: speed                    Display SPI bus speed
+Params: speed                   Display SPI bus speed
 
-        rotate                   Display rotation {0,90,180,270}
+        rotate                  Display rotation {0,90,180,270}
 
-        fps                      Delay between frame updates
+        fps                     Delay between frame updates
 
-        debug                    Debug output level {0-7}
+        debug                   Debug output level {0-7}
 
-        xohms                    Touchpanel sensitivity (X-plate resistance)
+        xohms                   Touchpanel sensitivity (X-plate resistance)
 
-        resetgpio                GPIO used to reset controller
+        resetgpio               GPIO used to reset controller
 
-        ledgpio                  GPIO used to control backlight
+        ledgpio                 GPIO used to control backlight
 
 
 Name:   hy28b
 Info:   HY28B - 2.8" TFT LCD Display Module by HAOYU Electronics
         Default values match Texy's display shield
 Load:   dtoverlay=hy28b,<param>=<val>
-Params: speed                    Display SPI bus speed
+Params: speed                   Display SPI bus speed
 
-        rotate                   Display rotation {0,90,180,270}
+        rotate                  Display rotation {0,90,180,270}
 
-        fps                      Delay between frame updates
+        fps                     Delay between frame updates
 
-        debug                    Debug output level {0-7}
+        debug                   Debug output level {0-7}
 
-        xohms                    Touchpanel sensitivity (X-plate resistance)
+        xohms                   Touchpanel sensitivity (X-plate resistance)
 
-        resetgpio                GPIO used to reset controller
+        resetgpio               GPIO used to reset controller
 
-        ledgpio                  GPIO used to control backlight
+        ledgpio                 GPIO used to control backlight
 
 
 Name:   i2c-gpio
 Info:   Adds support for software i2c controller on gpio pins
 Load:   dtoverlay=i2c-gpio,<param>=<val>
-Params: i2c_gpio_sda             GPIO used for I2C data (default "23")
+Params: i2c_gpio_sda            GPIO used for I2C data (default "23")
 
-        i2c_gpio_scl             GPIO used for I2C clock (default "24")
+        i2c_gpio_scl            GPIO used for I2C clock (default "24")
 
-        i2c_gpio_delay_us        Clock delay in microseconds
-                                 (default "2" = ~100kHz)
+        i2c_gpio_delay_us       Clock delay in microseconds
+                                (default "2" = ~100kHz)
 
 
 Name:   i2c-rtc
 Info:   Adds support for a number of I2C Real Time Clock devices
 Load:   dtoverlay=i2c-rtc,<param>=<val>
-Params: ds1307                   Select the DS1307 device
+Params: ds1307                  Select the DS1307 device
 
-        ds3231                   Select the DS3231 device
+        ds3231                  Select the DS3231 device
 
-        mcp7941x                 Select the MCP7941x device
+        mcp7941x                Select the MCP7941x device
 
-        pcf2127                  Select the PCF2127 device
+        pcf2127                 Select the PCF2127 device
 
-        pcf8523                  Select the PCF8523 device
+        pcf8523                 Select the PCF8523 device
 
-        pcf8563                  Select the PCF8563 device
+        pcf8563                 Select the PCF8563 device
 
 
 Name:   i2s-mmap
@@ -396,70 +396,70 @@ Name:   lirc-rpi
 Info:   Configures lirc-rpi (Linux Infrared Remote Control for Raspberry Pi)
         Consult the module documentation for more details.
 Load:   dtoverlay=lirc-rpi,<param>=<val>
-Params: gpio_out_pin             GPIO for output (default "17")
+Params: gpio_out_pin            GPIO for output (default "17")
 
-        gpio_in_pin              GPIO for input (default "18")
+        gpio_in_pin             GPIO for input (default "18")
 
-        gpio_in_pull             Pull up/down/off on the input pin
-                                 (default "down")
+        gpio_in_pull            Pull up/down/off on the input pin
+                                (default "down")
 
-        sense                    Override the IR receive auto-detection logic:
-                                   "0" = force active-high
-                                   "1" = force active-low
-                                   "-1" = use auto-detection
-                                 (default "-1")
+        sense                   Override the IR receive auto-detection logic:
+                                 "0" = force active-high
+                                 "1" = force active-low
+                                 "-1" = use auto-detection
+                                (default "-1")
 
-        softcarrier              Turn the software carrier "on" or "off"
-                                 (default "on")
+        softcarrier             Turn the software carrier "on" or "off"
+                                (default "on")
 
-        invert                   "on" = invert the output pin (default "off")
+        invert                  "on" = invert the output pin (default "off")
 
-        debug                    "on" = enable additional debug messages
-                                 (default "off")
+        debug                   "on" = enable additional debug messages
+                                (default "off")
 
 
 Name:   mcp2515-can0
 Info:   Configures the MCP2515 CAN controller on spi0.0
 Load:   dtoverlay=mcp2515-can0,<param>=<val>
-Params: oscillator               Clock frequency for the CAN controller (Hz)
+Params: oscillator              Clock frequency for the CAN controller (Hz)
 
-        spimaxfrequency          Maximum SPI frequence (Hz)
+        spimaxfrequency         Maximum SPI frequence (Hz)
 
-        interrupt                GPIO for interrupt signal
+        interrupt               GPIO for interrupt signal
 
 
 Name:   mcp2515-can1
 Info:   Configures the MCP2515 CAN controller on spi0.1
 Load:   dtoverlay=mcp2515-can1,<param>=<val>
-Params: oscillator               Clock frequency for the CAN controller (Hz)
+Params: oscillator              Clock frequency for the CAN controller (Hz)
 
-        spimaxfrequency          Maximum SPI frequence (Hz)
+        spimaxfrequency         Maximum SPI frequence (Hz)
 
-        interrupt                GPIO for interrupt signal
+        interrupt               GPIO for interrupt signal
 
 
 Name:   mmc
 Info:   Selects the bcm2835-mmc SD/MMC driver, optionally with overclock
 Load:   dtoverlay=mmc,<param>=<val>
-Params: overclock_50             Clock (in MHz) to use when the MMC framework
-                                 requests 50MHz
-        force_pio                Disable DMA support
+Params: overclock_50            Clock (in MHz) to use when the MMC framework
+                                requests 50MHz
+        force_pio               Disable DMA support
 
 
 Name:   mz61581
 Info:   MZ61581 display by Tontec
 Load:   dtoverlay=mz61581,<param>=<val>
-Params: speed                    Display SPI bus speed
+Params: speed                   Display SPI bus speed
 
-        rotate                   Display rotation {0,90,180,270}
+        rotate                  Display rotation {0,90,180,270}
 
-        fps                      Delay between frame updates
+        fps                     Delay between frame updates
 
-        txbuflen                 Transmit buffer length (default 32768)
+        txbuflen                Transmit buffer length (default 32768)
 
-        debug                    Debug output level {0-7}
+        debug                   Debug output level {0-7}
 
-        xohms                    Touchpanel sensitivity (X-plate resistance)
+        xohms                   Touchpanel sensitivity (X-plate resistance)
 
 
 [ The pcf2127-rtc overlay has been deleted. See i2c-rtc. ]
@@ -474,69 +474,69 @@ Params: speed                    Display
 Name:   piscreen
 Info:   PiScreen display by OzzMaker.com
 Load:   dtoverlay=piscreen,<param>=<val>
-Params: speed                    Display SPI bus speed
+Params: speed                   Display SPI bus speed
 
-        rotate                   Display rotation {0,90,180,270}
+        rotate                  Display rotation {0,90,180,270}
 
-        fps                      Delay between frame updates
+        fps                     Delay between frame updates
 
-        debug                    Debug output level {0-7}
+        debug                   Debug output level {0-7}
 
-        xohms                    Touchpanel sensitivity (X-plate resistance)
+        xohms                   Touchpanel sensitivity (X-plate resistance)
 
 
 Name:   piscreen2r
 Info:   PiScreen 2 with resistive TP display by OzzMaker.com
 Load:   dtoverlay=piscreen2r,<param>=<val>
-Params: speed                    Display SPI bus speed
+Params: speed                   Display SPI bus speed
 
-        rotate                   Display rotation {0,90,180,270}
+        rotate                  Display rotation {0,90,180,270}
 
-        fps                      Delay between frame updates
+        fps                     Delay between frame updates
 
-        debug                    Debug output level {0-7}
+        debug                   Debug output level {0-7}
 
-        xohms                    Touchpanel sensitivity (X-plate resistance)
+        xohms                   Touchpanel sensitivity (X-plate resistance)
 
 
 Name:   pitft28-capacitive
 Info:   Adafruit PiTFT 2.8" capacitive touch screen
 Load:   dtoverlay=pitft28-capacitive,<param>=<val>
-Params: speed                    Display SPI bus speed
+Params: speed                   Display SPI bus speed
 
-        rotate                   Display rotation {0,90,180,270}
+        rotate                  Display rotation {0,90,180,270}
 
-        fps                      Delay between frame updates
+        fps                     Delay between frame updates
 
-        debug                    Debug output level {0-7}
+        debug                   Debug output level {0-7}
 
-        touch-sizex              Touchscreen size x (default 240)
+        touch-sizex             Touchscreen size x (default 240)
 
-        touch-sizey              Touchscreen size y (default 320)
+        touch-sizey             Touchscreen size y (default 320)
 
-        touch-invx               Touchscreen inverted x axis
+        touch-invx              Touchscreen inverted x axis
 
-        touch-invy               Touchscreen inverted y axis
+        touch-invy              Touchscreen inverted y axis
 
-        touch-swapxy             Touchscreen swapped x y axis
+        touch-swapxy            Touchscreen swapped x y axis
 
 
 Name:   pitft28-resistive
 Info:   Adafruit PiTFT 2.8" resistive touch screen
 Load:   dtoverlay=pitft28-resistive,<param>=<val>
-Params: speed                    Display SPI bus speed
+Params: speed                   Display SPI bus speed
 
-        rotate                   Display rotation {0,90,180,270}
+        rotate                  Display rotation {0,90,180,270}
 
-        fps                      Delay between frame updates
+        fps                     Delay between frame updates
 
-        debug                    Debug output level {0-7}
+        debug                   Debug output level {0-7}
 
 
 Name:   pps-gpio
 Info:   Configures the pps-gpio (pulse-per-second time signal via GPIO).
 Load:   dtoverlay=pps-gpio,<param>=<val>
-Params: gpiopin                  Input GPIO (default "18")
+Params: gpiopin                 Input GPIO (default "18")
 
 
 Name:   pwm
@@ -553,9 +553,9 @@ Info:   Configures a single PWM channel
           4) Currently the clock must have been enabled and configured
              by other means.
 Load:   dtoverlay=pwm,<param>=<val>
-Params: pin                      Output pin (default 18) - see table
-        func                     Pin function (default 2 = Alt5) - see above
-        clock                    PWM clock frequency (informational)
+Params: pin                     Output pin (default 18) - see table
+        func                    Pin function (default 2 = Alt5) - see above
+        clock                   PWM clock frequency (informational)
 
 
 Name:   pwm-2chan
@@ -572,11 +572,11 @@ Info:   Configures both PWM channels
           4) Currently the clock must have been enabled and configured
              by other means.
 Load:   dtoverlay=pwm-2chan,<param>=<val>
-Params: pin                      Output pin (default 18) - see table
-        pin2                     Output pin for other channel (default 19)
-        func                     Pin function (default 2 = Alt5) - see above
-        func2                    Function for pin2 (default 2 = Alt5)
-        clock                    PWM clock frequency (informational)
+Params: pin                     Output pin (default 18) - see table
+        pin2                    Output pin for other channel (default 19)
+        func                    Pin function (default 2 = Alt5) - see above
+        func2                   Function for pin2 (default 2 = Alt5)
+        clock                   PWM clock frequency (informational)
 
 
 Name:   raspidac3
@@ -600,15 +600,15 @@ Params: <None>
 Name:   rpi-display
 Info:   RPi-Display - 2.8" Touch Display by Watterott
 Load:   dtoverlay=rpi-display,<param>=<val>
-Params: speed                    Display SPI bus speed
+Params: speed                   Display SPI bus speed
 
-        rotate                   Display rotation {0,90,180,270}
+        rotate                  Display rotation {0,90,180,270}
 
-        fps                      Delay between frame updates
+        fps                     Delay between frame updates
 
-        debug                    Debug output level {0-7}
+        debug                   Debug output level {0-7}
 
-        xohms                    Touchpanel sensitivity (X-plate resistance)
+        xohms                   Touchpanel sensitivity (X-plate resistance)
 
 
 Name:   rpi-ft5406
@@ -632,52 +632,52 @@ Params: <None>
 Name:   sdhost
 Info:   Selects the bcm2835-sdhost SD/MMC driver, optionally with overclock
 Load:   dtoverlay=sdhost,<param>=<val>
-Params: overclock_50             Clock (in MHz) to use when the MMC framework
-                                 requests 50MHz
+Params: overclock_50            Clock (in MHz) to use when the MMC framework
+                                requests 50MHz
 
-        force_pio                Disable DMA support (default off)
+        force_pio               Disable DMA support (default off)
 
-        pio_limit                Number of blocks above which to use DMA
-                                 (default 1)
+        pio_limit               Number of blocks above which to use DMA
+                                (default 1)
 
-        debug                    Enable debug output (default off)
+        debug                   Enable debug output (default off)
 
 
 Name:   sdio
 Info:   Selects the bcm2835-sdhost SD/MMC driver, optionally with overclock,
         and enables SDIO via GPIOs 22-27.
 Load:   dtoverlay=sdio,<param>=<val>
-Params: overclock_50             SD Clock (in MHz) to use when the MMC framework
-                                 requests 50MHz
+Params: overclock_50            SD Clock (in MHz) to use when the MMC framework
+                                requests 50MHz
 
-        sdio_overclock           SDIO Clock (in MHz) to use when the MMC
-                                 framework requests 50MHz
+        sdio_overclock          SDIO Clock (in MHz) to use when the MMC
+                                framework requests 50MHz
 
-        force_pio                Disable DMA support (default off)
+        force_pio               Disable DMA support (default off)
 
-        pio_limit                Number of blocks above which to use DMA
-                                 (default 1)
+        pio_limit               Number of blocks above which to use DMA
+                                (default 1)
 
-        debug                    Enable debug output (default off)
+        debug                   Enable debug output (default off)
 
-        poll_once                Disable SDIO-device polling every second
-                                 (default on: polling once at boot-time)
+        poll_once               Disable SDIO-device polling every second
+                                (default on: polling once at boot-time)
 
-        bus_width                Set the SDIO host bus width (default 4 bits)
+        bus_width               Set the SDIO host bus width (default 4 bits)
 
 
 Name:   sdtweak
 Info:   Tunes the bcm2835-sdhost SD/MMC driver
 Load:   dtoverlay=sdtweak,<param>=<val>
-Params: overclock_50             Clock (in MHz) to use when the MMC framework
-                                 requests 50MHz
+Params: overclock_50            Clock (in MHz) to use when the MMC framework
+                                requests 50MHz
 
-        force_pio                Disable DMA support (default off)
+        force_pio               Disable DMA support (default off)
 
-        pio_limit                Number of blocks above which to use DMA
-                                 (default 1)
+        pio_limit               Number of blocks above which to use DMA
+                                (default 1)
 
-        debug                    Enable debug output (default off)
+        debug                   Enable debug output (default off)
 
 
 Name:   smi
@@ -708,25 +708,25 @@ Name:   tinylcd35
 Info:   3.5" Color TFT Display by www.tinylcd.com
         Options: Touch, RTC, keypad
 Load:   dtoverlay=tinylcd35,<param>=<val>
-Params: speed                    Display SPI bus speed
+Params: speed                   Display SPI bus speed
 
-        rotate                   Display rotation {0,90,180,270}
+        rotate                  Display rotation {0,90,180,270}
 
-        fps                      Delay between frame updates
+        fps                     Delay between frame updates
 
-        debug                    Debug output level {0-7}
+        debug                   Debug output level {0-7}
 
-        touch                    Enable touch panel
+        touch                   Enable touch panel
 
-        touchgpio                Touch controller IRQ GPIO
+        touchgpio               Touch controller IRQ GPIO
 
-        xohms                    Touchpanel: Resistance of X-plate in ohms
+        xohms                   Touchpanel: Resistance of X-plate in ohms
 
-        rtc-pcf                  PCF8563 Real Time Clock
+        rtc-pcf                 PCF8563 Real Time Clock
 
-        rtc-ds                   DS1307 Real Time Clock
+        rtc-ds                  DS1307 Real Time Clock
 
-        keypad                   Enable keypad
+        keypad                  Enable keypad
 
         Examples:
             Display with touchpanel, PCF8563 RTC and keypad:
@@ -738,9 +738,9 @@ Params: speed                    Display
 Name:   uart1
 Info:   Enable uart1 in place of uart0
 Load:   dtoverlay=uart1,<param>=<val>
-Params: txd1_pin                 GPIO pin for TXD1 (14, 32 or 40 - default 14)
+Params: txd1_pin                GPIO pin for TXD1 (14, 32 or 40 - default 14)
 
-        rxd1_pin                 GPIO pin for RXD1 (15, 33 or 41 - default 15)
+        rxd1_pin                GPIO pin for RXD1 (15, 33 or 41 - default 15)
 
 
 Name:   vc4-kms-v3d
@@ -763,22 +763,22 @@ Name:   w1-gpio
 Info:   Configures the w1-gpio Onewire interface module.
         Use this overlay if you *don't* need a GPIO to drive an external pullup.
 Load:   dtoverlay=w1-gpio,<param>=<val>
-Params: gpiopin                  GPIO for I/O (default "4")
+Params: gpiopin                 GPIO for I/O (default "4")
 
-        pullup                   Non-zero, "on", or "y" to enable the parasitic
-                                 power (2-wire, power-on-data) feature
+        pullup                  Non-zero, "on", or "y" to enable the parasitic
+                                power (2-wire, power-on-data) feature
 
 
 Name:   w1-gpio-pullup
 Info:   Configures the w1-gpio Onewire interface module.
         Use this overlay if you *do* need a GPIO to drive an external pullup.
 Load:   dtoverlay=w1-gpio-pullup,<param>=<val>
-Params: gpiopin                  GPIO for I/O (default "4")
+Params: gpiopin                 GPIO for I/O (default "4")
 
-        pullup                   Non-zero, "on", or "y" to enable the parasitic
-                                 power (2-wire, power-on-data) feature
+        pullup                  Non-zero, "on", or "y" to enable the parasitic
+                                power (2-wire, power-on-data) feature
 
-        extpullup                GPIO for external pullup (default "5")
+        extpullup               GPIO for external pullup (default "5")
 
 
 Troubleshooting