openwrt_lede/target/linux/mvebu/patches-4.4/053-ARM-dts-Add-SolidRun-Armada-388-Clearfog-A1-DT-file.patch

From 4c945e8556ec7ea5b19d4f8721b212f468656e0d Mon Sep 17 00:00:00 2001
From: Russell King <rmk+kernel@arm.linux.org.uk>
Date: Sun, 6 Dec 2015 21:52:06 +0000
Subject: [PATCH] ARM: dts: Add SolidRun Armada 388 Clearfog A1 DT file

Add support for the SolidRun Armada 388 Clearfog A1 board.  This board
has an Armada 388 microsom, dedicated gigabit ethernet, six switched
gigabit ethernet ports, SFP cage, two Mini-PCIe/mSATA slots, a m.2 SATA
slot, and a MikroBUS connector to allow MikroBUS modules to be added.

This DT file adds support for all board facilities with the exception
of full SFP support.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
---
 arch/arm/boot/dts/Makefile                         |   1 +
 arch/arm/boot/dts/armada-388-clearfog.dts          | 456 +++++++++++++++++++++
 .../arm/boot/dts/armada-38x-solidrun-microsom.dtsi | 115 ++++++
 3 files changed, 572 insertions(+)
 create mode 100644 arch/arm/boot/dts/armada-388-clearfog.dts
 create mode 100644 arch/arm/boot/dts/armada-38x-solidrun-microsom.dtsi

--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -750,6 +750,7 @@ dtb-$(CONFIG_MACH_ARMADA_38X) += \
 	armada-385-linksys-cobra.dtb \
 	armada-385-linksys-rango.dtb \
 	armada-385-linksys-shelby.dtb \
+	armada-388-clearfog.dtb \
 	armada-388-db.dtb \
 	armada-388-gp.dtb \
 	armada-388-rd.dtb
--- /dev/null
+++ b/arch/arm/boot/dts/armada-388-clearfog.dts
@@ -0,0 +1,456 @@
+/*
+ * Device Tree file for SolidRun Clearfog revision A1 rev 2.0 (88F6828)
+ *
+ *  Copyright (C) 2015 Russell King
+ *
+ * This board is in development; the contents of this file work with
+ * the A1 rev 2.0 of the board, which does not represent final
+ * production board.  Things will change, don't expect this file to
+ * remain compatible info the future.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License
+ *     version 2 as published by the Free Software Foundation.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "armada-388.dtsi"
+#include "armada-38x-solidrun-microsom.dtsi"
+
+/ {
+	model = "SolidRun Clearfog A1";
+	compatible = "solidrun,clearfog-a1", "marvell,armada388",
+		"marvell,armada385", "marvell,armada380";
+
+	aliases {
+		/* So that mvebu u-boot can update the MAC addresses */
+		ethernet1 = &eth0;
+		ethernet2 = &eth1;
+		ethernet3 = &eth2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	reg_3p3v: regulator-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "3P3V";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-always-on;
+	};
+
+	soc {
+		internal-regs {
+			ethernet@30000 {
+				phy-mode = "sgmii";
+				status = "okay";
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+
+			ethernet@34000 {
+				phy-mode = "sgmii";
+				status = "okay";
+
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+
+			i2c@11000 {
+				/* Is there anything on this? */
+				clock-frequency = <100000>;
+				pinctrl-0 = <&i2c0_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+
+				/*
+				 * PCA9655 GPIO expander, up to 1MHz clock.
+				 *  0-CON3 CLKREQ#
+				 *  1-CON3 PERST#
+				 *  2-CON2 PERST#
+				 *  3-CON3 W_DISABLE
+				 *  4-CON2 CLKREQ#
+				 *  5-USB3 overcurrent
+				 *  6-USB3 power
+				 *  7-CON2 W_DISABLE
+				 *  8-JP4 P1
+				 *  9-JP4 P4
+				 * 10-JP4 P5
+				 * 11-m.2 DEVSLP
+				 * 12-SFP_LOS
+				 * 13-SFP_TX_FAULT
+				 * 14-SFP_TX_DISABLE
+				 * 15-SFP_MOD_DEF0
+				 */
+				expander0: gpio-expander@20 {
+					/*
+					 * This is how it should be:
+					 * compatible = "onnn,pca9655",
+					 *	 "nxp,pca9555";
+					 * but you can't do this because of
+					 * the way I2C works.
+					 */
+					compatible = "nxp,pca9555";
+					gpio-controller;
+					#gpio-cells = <2>;
+					reg = <0x20>;
+
+					pcie1_0_clkreq {
+						gpio-hog;
+						gpios = <0 GPIO_ACTIVE_LOW>;
+						input;
+						line-name = "pcie1.0-clkreq";
+					};
+					pcie1_0_w_disable {
+						gpio-hog;
+						gpios = <3 GPIO_ACTIVE_LOW>;
+						output-low;
+						line-name = "pcie1.0-w-disable";
+					};
+					pcie2_0_clkreq {
+						gpio-hog;
+						gpios = <4 GPIO_ACTIVE_LOW>;
+						input;
+						line-name = "pcie2.0-clkreq";
+					};
+					pcie2_0_w_disable {
+						gpio-hog;
+						gpios = <7 GPIO_ACTIVE_LOW>;
+						output-low;
+						line-name = "pcie2.0-w-disable";
+					};
+					usb3_ilimit {
+						gpio-hog;
+						gpios = <5 GPIO_ACTIVE_LOW>;
+						input;
+						line-name = "usb3-current-limit";
+					};
+					usb3_power {
+						gpio-hog;
+						gpios = <6 GPIO_ACTIVE_HIGH>;
+						output-high;
+						line-name = "usb3-power";
+					};
+					m2_devslp {
+						gpio-hog;
+						gpios = <11 GPIO_ACTIVE_HIGH>;
+						output-low;
+						line-name = "m.2 devslp";
+					};
+					sfp_los {
+						/* SFP loss of signal */
+						gpio-hog;
+						gpios = <12 GPIO_ACTIVE_HIGH>;
+						input;
+						line-name = "sfp-los";
+					};
+					sfp_tx_fault {
+						/* SFP laser fault */
+						gpio-hog;
+						gpios = <13 GPIO_ACTIVE_HIGH>;
+						input;
+						line-name = "sfp-tx-fault";
+					};
+					sfp_tx_disable {
+						/* SFP transmit disable */
+						gpio-hog;
+						gpios = <14 GPIO_ACTIVE_HIGH>;
+						output-low;
+						line-name = "sfp-tx-disable";
+					};
+					sfp_mod_def0 {
+						/* SFP module present */
+						gpio-hog;
+						gpios = <15 GPIO_ACTIVE_LOW>;
+						input;
+						line-name = "sfp-mod-def0";
+					};
+				};
+
+				/* The MCP3021 is 100kHz clock only */
+				mikrobus_adc: mcp3021@4c {
+					compatible = "microchip,mcp3021";
+					reg = <0x4c>;
+				};
+
+				/* Also something at 0x64 */
+			};
+
+			i2c@11100 {
+				/*
+				 * Routed to SFP, mikrobus, and PCIe.
+				 * SFP limits this to 100kHz, and requires
+				 *  an AT24C01A/02/04 with address pins tied
+				 *  low, which takes addresses 0x50 and 0x51.
+				 * Mikrobus doesn't specify beyond an I2C
+				 *  bus being present.
+				 * PCIe uses ARP to assign addresses, or
+				 *  0x63-0x64.
+				 */
+				clock-frequency = <100000>;
+				pinctrl-0 = <&clearfog_i2c1_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+			};
+
+			mdio@72004 {
+				pinctrl-0 = <&mdio_pins>;
+				pinctrl-names = "default";
+
+				phy_dedicated: ethernet-phy@0 {
+					/*
+					 * Annoyingly, the marvell phy driver
+					 * configures the LED register, rather
+					 * than preserving reset-loaded setting.
+					 * We undo that rubbish here.
+					 */
+					marvell,reg-init = <3 16 0 0x101e>;
+					reg = <0>;
+				};
+			};
+
+			pinctrl@18000 {
+				clearfog_dsa0_clk_pins: clearfog-dsa0-clk-pins {
+					marvell,pins = "mpp46";
+					marvell,function = "ref";
+				};
+				clearfog_dsa0_pins: clearfog-dsa0-pins {
+					marvell,pins = "mpp23", "mpp41";
+					marvell,function = "gpio";
+				};
+				clearfog_i2c1_pins: i2c1-pins {
+					/* SFP, PCIe, mSATA, mikrobus */
+					marvell,pins = "mpp26", "mpp27";
+					marvell,function = "i2c1";
+				};
+				clearfog_sdhci_cd_pins: clearfog-sdhci-cd-pins {
+					marvell,pins = "mpp20";
+					marvell,function = "gpio";
+				};
+				clearfog_sdhci_pins: clearfog-sdhci-pins {
+					marvell,pins = "mpp21", "mpp28",
+						       "mpp37", "mpp38",
+						       "mpp39", "mpp40";
+					marvell,function = "sd0";
+				};
+				clearfog_spi1_cs_pins: spi1-cs-pins {
+					marvell,pins = "mpp55";
+					marvell,function = "spi1";
+				};
+				mikro_pins: mikro-pins {
+					/* int: mpp22 rst: mpp29 */
+					marvell,pins = "mpp22", "mpp29";
+					marvell,function = "gpio";
+				};
+				mikro_spi_pins: mikro-spi-pins {
+					marvell,pins = "mpp43";
+					marvell,function = "spi1";
+				};
+				mikro_uart_pins: mikro-uart-pins {
+					marvell,pins = "mpp24", "mpp25";
+					marvell,function = "ua1";
+				};
+				rear_button_pins: rear-button-pins {
+					marvell,pins = "mpp34";
+					marvell,function = "gpio";
+				};
+			};
+
+			sata@a8000 {
+				/* pinctrl? */
+				status = "okay";
+			};
+
+			sata@e0000 {
+				/* pinctrl? */
+				status = "okay";
+			};
+
+			sdhci@d8000 {
+				bus-width = <4>;
+				cd-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
+				no-1-8-v;
+				pinctrl-0 = <&clearfog_sdhci_pins
+					     &clearfog_sdhci_cd_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+				vmmc = <&reg_3p3v>;
+				wp-inverted;
+			};
+
+			serial@12100 {
+				/* mikrobus uart */
+				pinctrl-0 = <&mikro_uart_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+			};
+
+			spi@10680 {
+				/*
+				 * We don't seem to have the W25Q32 on the
+				 * A1 Rev 2.0 boards, so disable SPI.
+				 * CS0: W25Q32 (doesn't appear to be present)
+				 * CS1:
+				 * CS2: mikrobus
+				 */
+				pinctrl-0 = <&spi1_pins
+					     &clearfog_spi1_cs_pins
+					     &mikro_spi_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+
+				spi-flash@0 {
+					#address-cells = <1>;
+					#size-cells = <0>;
+					compatible = "w25q32", "jedec,spi-nor";
+					reg = <0>; /* Chip select 0 */
+					spi-max-frequency = <3000000>;
+					status = "disabled";
+				};
+			};
+
+			usb@58000 {
+				/* CON3, nearest  power. */
+				status = "okay";
+			};
+
+			usb3@f0000 {
+				/* CON2, nearest CPU, USB2 only. */
+				status = "okay";
+			};
+
+			usb3@f8000 {
+				/* CON7 */
+				status = "okay";
+			};
+		};
+
+		pcie-controller {
+			status = "okay";
+			/*
+			 * The two PCIe units are accessible through
+			 * the mini-PCIe connectors on the board.
+			 */
+			pcie@2,0 {
+				/* Port 1, Lane 0. CON3, nearest power. */
+				reset-gpios = <&expander0 1 GPIO_ACTIVE_LOW>;
+				status = "okay";
+			};
+			pcie@3,0 {
+				/* Port 2, Lane 0. CON2, nearest CPU. */
+				reset-gpios = <&expander0 2 GPIO_ACTIVE_LOW>;
+				status = "okay";
+			};
+		};
+	};
+
+	dsa@0 {
+		compatible = "marvell,dsa";
+		dsa,ethernet = <&eth1>;
+		dsa,mii-bus = <&mdio>;
+		pinctrl-0 = <&clearfog_dsa0_clk_pins &clearfog_dsa0_pins>;
+		pinctrl-names = "default";
+		#address-cells = <2>;
+		#size-cells = <0>;
+
+		switch@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <4 0>;
+
+			port@0 {
+				reg = <0>;
+				label = "lan1";
+			};
+
+			port@1 {
+				reg = <1>;
+				label = "lan2";
+			};
+
+			port@2 {
+				reg = <2>;
+				label = "lan3";
+			};
+
+			port@3 {
+				reg = <3>;
+				label = "lan4";
+			};
+
+			port@4 {
+				reg = <4>;
+				label = "lan5";
+			};
+
+			port@5 {
+				reg = <5>;
+				label = "cpu";
+			};
+
+			port@6 {
+				/* 88E1512 external phy */
+				reg = <6>;
+				label = "lan6";
+				fixed-link {
+					speed = <1000>;
+					full-duplex;
+				};
+			};
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		pinctrl-0 = <&rear_button_pins>;
+		pinctrl-names = "default";
+
+		button_0 {
+			/* The rear SW3 button */
+			label = "Rear Button";
+			gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+			linux,can-disable;
+			linux,code = <BTN_0>;
+		};
+	};
+};
--- /dev/null
+++ b/arch/arm/boot/dts/armada-38x-solidrun-microsom.dtsi
@@ -0,0 +1,115 @@
+/*
+ * Device Tree file for SolidRun Armada 38x Microsom
+ *
+ *  Copyright (C) 2015 Russell King
+ *
+ * This board is in development; the contents of this file work with
+ * the A1 rev 2.0 of the board, which does not represent final
+ * production board.  Things will change, don't expect this file to
+ * remain compatible info the future.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License
+ *     version 2 as published by the Free Software Foundation.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	memory {
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>; /* 256 MB */
+	};
+
+	soc {
+		ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+			  MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
+			  MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
+			  MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000>;
+
+		internal-regs {
+			ethernet@70000 {
+				pinctrl-0 = <&ge0_rgmii_pins>;
+				pinctrl-names = "default";
+				phy = <&phy_dedicated>;
+				phy-mode = "rgmii-id";
+				status = "okay";
+			};
+
+			mdio@72004 {
+				/*
+				 * Add the phy clock here, so the phy can be
+				 * accessed to read its IDs prior to binding
+				 * with the driver.
+				 */
+				pinctrl-0 = <&mdio_pins &microsom_phy_clk_pins>;
+				pinctrl-names = "default";
+
+				phy_dedicated: ethernet-phy@0 {
+					/*
+					 * Annoyingly, the marvell phy driver
+					 * configures the LED register, rather
+					 * than preserving reset-loaded setting.
+					 * We undo that rubbish here.
+					 */
+					marvell,reg-init = <3 16 0 0x101e>;
+					reg = <0>;
+				};
+			};
+
+			pinctrl@18000 {
+				microsom_phy_clk_pins: microsom-phy-clk-pins {
+					marvell,pins = "mpp45";
+					marvell,function = "ref";
+				};
+			};
+
+			rtc@a3800 {
+				/*
+				 * If the rtc doesn't work, run "date reset"
+				 * twice in u-boot.
+				 */
+				status = "okay";
+			};
+
+			serial@12000 {
+				pinctrl-0 = <&uart0_pins>;
+				pinctrl-names = "default";
+				status = "okay";
+			};
+		};
+	};
+};